EMM386 Troubleshooting and Technical Information (78557)



The information in this article applies to:
    Microsoft MS-DOS operating system 5.0
    Microsoft MS-DOS operating system 5.0a
    Microsoft MS-DOS operating system 6.0
    Microsoft MS-DOS operating system 6.2
    Microsoft MS-DOS operating system 6.21
    Microsoft MS-DOS operating system 6.22
    Microsoft Windows for Workgroups 3.1
    Microsoft Windows for Workgroups 3.11
    Microsoft Windows 3.1
    Microsoft Windows 3.11
    Microsoft Windows 95
    Microsoft Windows 98

This article was previously published under Q78557
If this article does not describe your hardware-related issue, please see the following Microsoft Web site to view more articles about hardware:

SUMMARY

The following topics are discussed in this article:
    Troubleshooting steps to use if EMM386.EXE locks up the computer
    How EMM386.EXE locates UMBs and the EMS page frame:

    UMA scanning algorithm
    EMM386 and the E000 segment


    Common EMS questions concerning the following:
      "WARNING: Unable to set page frame base address--EMS unavailable" message
      "Size of expanded memory pool adjusted" message
      EMM386.EXE and Windows

    EMM386.EXE version history
NOTE: This information applies to the versions of EMM386.EXE included with MS-DOS, Microsoft Windows, and Microsoft Windows for Workgroups.

MORE INFORMATION

IF EMM386.EXE LOCKS UP THE COMPUTER

If EMM386.EXE locks up the computer, follow these troubleshooting steps:

    If the DEVICE=EMM386.EXE in the CONFIG.SYS file contains the HIGHSCAN parameter, remove HIGHSCAN from the command, save the CONFIG.SYS file, and restart your computer. (HIGHSCAN cannot be used on some computers.)
    Start EMM386.EXE with the exclude option.

    EMM386.EXE may have incorrectly identified an area being used by the system as a "hole" (a region that can be used as a UMB or an EMS page frame). As a result, EMM386.EXE overwrites a portion of memory that is used by a hardware adapter in your computer.

    By excluding addresses in the range A000-EFFF, EMM386.EXE does not use any part of the excluded region for a UMB or EMS page frame. Identifying the correct region(s) to exclude requires experimentation. Start by excluding a large region and then reducing the size of the region. For example:
          DEVICE=EMM386.EXE NOEMS X=A000-EFFF
    
          DEVICE=EMM386.EXE NOEMS X=C000-DFFF
    
          DEVICE=EMM386.EXE NOEMS X=C800-CFFF
    
    You can use multiple exclusions on the EMM386.EXE device line. For example:
          DEVICE=EMM386.EXE NOEMS X=C000-C7FF X=E000-EFFF
    
    Refer to the documentation included with your hardware device(s) for information on the upper memory addresses the adapter card uses. Examples of devices that use upper memory addresses include network cards, SCSI adapters, video cards, and scanners.
    If your computer has a SCSI disk controller and requires a device driver for the SCSI adapter, be sure the DEVICE= line for the SCSI driver appears before the DEVICE=EMM386.EXE line. Examples of SCSI device drivers include ASPI4DOS.SYS and USPI14.SYS.
    If you are experiencing problems with the computer hanging, try loading the SMARTDrive double buffer driver.

    NOTE: The SMARTDrive double buffer driver line should appear before the DEVICE=EMM386.EXE line in the CONFIG.SYS file.

    MS-DOS 6.0 or later, Windows 3.1 or later, or Windows for Workgroups

    If you use MS-DOS 6.0 or later, Microsoft Windows 3.1 or later, or Microsoft Windows for Workgroups the SMARTDrive double buffer driver is loaded from the CONFIG.SYS file as follows:
          device=c:\windows\smartdrv.exe /double_buffer
    
    In the AUTOEXEC.BAT file, add a /L to the end of the SMARTDRV.EXE line. For example:
          c:\windows\smartdrv.exe /L
    
    If the problems persist, add a plus sign (+) to the end of the double buffer device line as follows:
          device=c:\windows\smartdrv.exe /double_buffer+
    

    MS-DOS 5.x

    If you use the SMARTDRV.SYS driver included with MS-DOS 5.x the SMARTDrive double buffer driver is loaded in the CONFIG.SYS as follows:
          device=c:\dos\smartdrv.sys /b+
    

    Experiment with different HIMEM.SYS A20 handlers. This is done using the /MACHINE: switch on the HIMEM.SYS device line.

    For information on the HIMEM.SYS /MACHINE: switch and troubleshooting A20 handler problems:
      Consult your MS-DOS, Windows, or Windows for Workgroups documentation -or-


      Query on the following words in the Microsoft Knowledge Base:

      tshoot and himem.sys and control and a20 line

HOW EMM386.EXE LOCATES UMBs AND THE EMS PAGE FRAME

UMA Scanning Algorithm

By default EMM386.EXE scans the following UMA region:
   MS-DOS 5.0: C800-DFFF

   Windows 3.1, Windows for Workgroups 3.1: C600-DFFF

   MS-DOS 6.0 and later, Windows for Workgroups 3.11 and later: C000-EFFF
NOTES:

The E000-EFFF region is handled differently on certain hardware (see the following section).

Under MS-DOS 6.0 and later and Windows for Workgroups 3.11, the F000-F7FF range can be included by using the HIGHSCAN switch.

EMM386.EXE and the E000 Segment

On Compaq machines, the E000 segment has either shadow RAM or the segment is unused. For shadow RAM, the shadow area is reclaimed by EMM386.EXE if the Int 10 vector has not been hooked before EMM386.EXE loads. This is because the shadow region contains a remapped copy of the video ROM from the C000 region.

EMM368.EXE excludes E000 on MCA machines (IBM PS/2s) since the E000 segment has the system ROM.

On other machines, E000 may be excluded by default. If you think the E000 range is available, you can explicitly include the E000 segment by adding I=E000-EFFF to the DEVICE=EMM386.EXE command in the CONFIG.SYS file.

NOTE: When EMM386.EXE encounters the include switch, it includes the region without scanning it for potential conflicts.

COMMON EMS ISSUES

WARNING: Unable to Set Page Frame Base Address--EMS Unavailable

This error is displayed if EMM386.EXE cannot locate a 64K contiguous "hole" in the UMA for the EMS page frame.

According to the LIM 3.2 specification, a page frame consists of four contiguous 16K pages, and a LIM provider must set the page frame.

According to the LIM 4.0 specification, an EMS provider need not set a 64K page frame, but it should set a 16K page at the minimum.

Although EMM386.EXE conforms to the LIM 4.0 specification, it does not load as an EMS provider if it does not find a 64K contiguous hole that can be used for the page frame. This is because the majority of LIM 3.2 applications assume the existence of a page frame.

EMM386.EXE can be forced to load without a LIM 3.2 (64K) page frame by using the Pn parameters. If you force EMM386.EXE to load as a LIM 4.0 provider, do not attempt to run LIM 3.2 applications. Consult with your application vendor to determine the required LIM version.

NOTE: If you require a LIM 3.2 (64K) page frame, it may be necessary to modify the settings on your hardware devices to free a contiguous, 64K region in the UMA.

Size of Expanded Memory Pool Adjusted

This error message is displayed if EMM386.EXE cannot provide all the EMS memory requested on the command line. For example, if you use the DEVICE=EMM386.EXE 2048 and your computer only has 1024K of XMS memory, EMM386.EXE displays this error message and provides as much EMS as possible. (Note that EMM386.EXE uses some XMS memory for its own code and data, and this reduces the amount of XMS memory available for EMS.)

Windows Cannot Provide EMS with the NOEMS Switch

According to the LIM 4.0 specification, an EMS page can also reside in conventional memory (0-640K). The EMM386 EMS line starts at 256K by default. If the NOEMS option is specified, all the holes in the adapter region A000-FFFF are used for UMBs, and EMM386.EXE does not provide any EMS.

Once Windows 3.0 is started and an MS-DOS session is started, EMM386.EXE may or may not be able to provide EMS. If Windows is running in 386 enhanced mode, EMM386.EXE can provide EMS in an MS-DOS session; however, the EMS pages are in conventional memory. This can cause problems because of the behavior of LIM 3.2 applications as described above.

In a Windows 3.1 386 enhanced mode MS-DOS session, EMS is not provided.

EMM386.EXE VERSION HISTORY

MS-DOS 5.0                    4.20
MS-DOS 5.00a                  4.33
MS-DOS 6.0                    4.45
MS-DOS 6.2                    4.48
MS-DOS 6.21                   4.48
MS-DOS 6.22                   4.49
Windows 3.1                   4.44
Windows 3.11                  4.44
Windows for Workgroups 3.1    4.44
Windows for Workgroups 3.11   4.48
Windows 95                    4.95
Windows 98                    4.95
Some of the products included here are manufactured by vendors independent of Microsoft; we make no warranty, implied or otherwise, regarding the performance or reliability of these products.

Modification Type: Major Last Reviewed: 5/12/2003
Keywords: kbinfo kbtshoot KB78557 kbAudDeveloper